An electric forklift fork to take goods. Forklift fork to take goods in the process, can be summarized as eight action.
02-27
An electric forklift fork to take goods. Forklift fork to take goods in the process, can be summarized as eight action.
1, approaching the cargo pile. After starting the truck, according
liftstar electric riding pallet jack to the position of the goods pile driving truck driving to the front of the cargo pile stops.
2, the vertical mast. Gear lever into neutral after a parked truck, will push the joystick forward, the mast to recover to a vertical position.
3, adjust the fork height. Pull back on the joystick movements, lifting forks, fork tines make alignment cargo space or pallet fork next hole.
4, into the fork pickup. The shift lever forward into a block, slow moving truck forward, so that goods skewer into the fork holes or tray under the cargo space. When contacted wishbone cargo truck braking.
5, micro-delivery fork. Pull back on the joystick movements so that the fork truck can leave the run up to the height.
6, after tilting mast. Pull back on the joystick, the mast back to the limit position.
7, exit cargo. After hanging down a gear shift lever to ease the brake, the truck can fall back to the position of the goods.
8, adjust the fork height. Push the joystick forward movements, down to the delivery of goods from the ground 200-300mm fork height. Back to start, sail Fanghuo location.
Second, the electric forklifts unload cargo. Forklift unloading process can be summarized as eight action.
1, approaching cargo. Place a parked truck unloading sail, good preparation for discharge.
2, adjust the fork height. Pull back on the joystick movements and cargo for delivery of goods that must be crossed l alignment height.
3, into the car on the bit. The shift lever is placed forward gears, truck slowly forward, so that the fork is located to be put above the parking brake goods (tray) at.
4, the vertical mast. Push the joystick forward tilt mast forward, recover to a vertical position. There slope, allowing the mast forward.
5, drop the fork unloading. Push the joystick forward lift that fork slow decline, the goods (pallets) smoothly on goods pile, then forks a little off the bottom of goods.
6, return the car pumping fork. After the shift lever into reverse gear,
liftstar Electric store Positioner ease brake, the truck back to the fork can fall away.
7, after tilting mast. Pull back on the joystick, the door frame was poured into extreme positions.
8, adjust the fork height. Push the joystick forward movements, from the ground next to a 200-300mm fork delivery of goods at the truck to leave, heading Pickup location to begin the next round of work to take delivery of the goods.
Let the driver feel comfortable
12-02
Let the driver feel comfortable Comfort of the driver to ensure the efficient operation of the forklift is very important. Earthworm especially for the driver to create a safe and comfortable driving environment. Dragon of the forklift driver's seat adjustment with a full range of features: seat backrest can be tilted forward or backward , seat springs can be adjusted , the seat can be moved forward or backward . It's all ergonomic , fully consider the needs of the driver's body , tailor the most comfortable way of driving . Allows the driver a sense of security Improper operation of the forklift may cause security risks, these improper actions include : do not slow down when cornering , while driving increased load, truck overloading , tilt , soft ground travel and so on. Drivers try to avoid these unsafe operations should operate. With the widespread use of forklift trucks in the production process , forklift safety issues more important. Truck has been designed to provide maximum operator safety factor of driving , the risk of damage and minimize truck . longChinese earthworm forklift safety device comprising the following : a safety device is activated when the engine safety device when the cover is opened and the engine , i.e. the engine is running , such as opening the engine cover , a safety device configured to control the truck does not start the engine .
Hand pallet truck oil should be checked once a month
12-02
1, refueling Hand pallet truck oil should be checked once a month. Recommend the use of hydraulic oil: ISOVG32, at 40 its kinematic viscosity of 32cSt, a total of about 0.3 liters. 2, the exhaust Due to transportation or inverted pump, the air is likely to enter the pump, which will result in a raised position to suppress, the stock pressure does not rise. According to the following methods exhaust: the finger (LOWER) pull to the lowered position, vertical reciprocating motion several times. 3, routine inspection and maintenance Routine maintenance is essential and should focus on the core axis and overhaul of wheels and rags, etc. When transporting finished goods should be removed on the fork and fork down to the lowest position. 4, oil In the factory, all the bearings and shaft has been coupled with a long-life oil, you just intermittently during the month, or every time a thorough inspection of all moving parts to add oil.
Jinzhou Huayuan Fuwa Heavy Machinery M & Co
10-30
the large-scale integration lifting mode become the development direction of large tonnage crawler cranes rapid increase in demand , China's leading enterprises have started construction crane develop large-tonnage products. Beginning in 2009 , Zoomlion , Sany, XCMG Fuwa Heavy Industry and launched a kiloton crawler cranes. Currently, XCMG crawler crane 2000t level has also been unveiled , Zoomlion 3200t design and development is underway. Large tonnage crawler cranes , it not only makes our country to rid itself of this type of product is completely dependent on imports of the situation , but also fully demonstrates the technological level of domestic production and manufacturing capacity .
Construction crane industry industrial restructuring in the enterprise development strategy deepening . In 2006, Terex acquired 50% equity interest from long ; 2008 , Liugong acquisition Bengbu Vibro Engineering Machinery Co., Ltd. Jinzhou Huayuan Fuwa Heavy Machinery M & Co., Ltd., a joint venture Manitowoc Dongyue Heavy Industries and etc., are the development of the enterprise and a significant impact on the industry , and are fully reflected in 2009 . In 2009, Anhui Liugong sales revenue grew 72.7% , cranes sales grew 62% ; ask dug Heavy brocade truck crane 297 units sold , an increase of 234% ; Hoisting Machinery Co., Ltd. Sany Automobile sales jumped cars crane 's first three production enterprises ; Jingcheng Heavy recovery truck crane machine production , when it achieved sales of 83 units of the good results . 2009 , XCMG and Zoomlion Mobile Crane Branch 2 industry profits accounted for 95.5% of total profits .