Hand Pallet Truck maintenance to say fine, in addition to a maintenance, there are two maintenance:
02-27
One: keep the hydraulic oil clean
The hydraulic oil is stored in a clean area, care must be taken when adding hydraulic oil change. Use only clean the filter with a fine grid funnel the oil from the container into the truck cylinder. Hebei earthworm is recommended that you use the hydraulic oil should be the device of the type recommended by the manufacturer.
Two: keep the system clean
Periodic replacement of hydraulic oil and oil seals. Good hydraulic oils
liftstar scissor lift table contain a variety of additives, which prevent deterioration of the oil or clogged system components. However, these additives lose effectiveness over time. Therefore, oil should be changed regularly to ensure that the role of additives. Filters can only absorb a limited number of dirt particles and other impurities from the oil. The recommended filter replacement cycle, in order to keep the system clean.
Three: keep clean areas clean about
1, when the maintenance truck cylinder hydraulic system, can only be used to clean the plastic bulkhead seal the ends of the pipeline.
2, maintenance of hydraulic components, workstations must be absolutely clean. Check status of the use of tools. They should also be very clean.
To refuel or refill the tank, make sure to clean the area around the filter cover. Use only clean oil and funnel or container. Never dirt into the system - only clean oil.
the fuel tank when refueling or re- oiling
12-04
Chinese Dragon of hand pallet trucks daily use and maintenance of common sense description: First : Keep the work area clean the fuel tank when refueling or re- oiling , be sure to clean the area around the filter cover . Use only clean oil and funnel or container. Never dirt into the system - only clean oil. 2 when the maintenance truck cylinder hydraulic system, can only clean plastic bulkhead for sealing the ends of the pipeline . 3, the maintenance of hydraulic components , workstations must be absolutely clean. Checking the condition of the tool . They should also be very clean. Second : to keep the hydraulic oil clean The hydraulic oil stored in a clean location, you must be careful when you add hydraulic oil change . Use only clean with a fine grid filter funnel the oil from the container into the truck fuel tank . Of course , it is recommended that you use the hydraulic oil should be recommended by the manufacturer of the device type . Finally : keep the system clean Periodic replacement of hydraulic oil and oil seals . Contains many good hydraulic oil additives, which prevent deterioration of the oil or clogged system components. However, these additives may lose effectiveness over time . Therefore, the oil should be changed regularly to ensure that additives play a role. Filters can only absorb a limited amount of dirt particles and other impurities from the oil. The proposed cycle by replacing the filter in order to keep the system clean.
the hydraulic system can be divided into open and closed systems
12-04
Almost all modern mechanical engineering with a hydraulic system, and electronic systems, computer control technology combined, has become an important part of modern construction machinery. Full merits of the mechanical properties of hydraulic transmission, hydraulic system performance depends primarily on the quality. Specifications of hydraulic components, variety, quality and performance improvement, especially after the introduction of new technologies and new technology electronic technology, servo technology, greatly improving the quality of the hydraulic system. Different forms of the truck hydraulic system: (1) by way of the oil cycle, the hydraulic system can be divided into open and closed systems. (2) the number of pump system according to, can be divided into single-pump system, dual pump systems and multi-pump systems. (3) by the use of different forms of the pump, and the pump system can be divided into a quantitative variable pump system. (4) different ways to perform component supply, the system can be divided into series and parallel systems.
With forging hydraulic press used with large workpieces
10-30
Injection Mixer for lifting hot metal, steel furnaces and continuous injection of molten steel ingot lifting equipment or ingot molds and other purposes. Main car lifting ladles, ladles, Vice car to flip and other auxiliary work.
2 clamp crane:
The use of high-temperature steel ingot clamp vertically lifted onto a soaking pit furnace, or put it out into the car shipped ingot.
3 off the ingot crane:
From the ingot ingot molds used to force prolapse. Small car off the ingots have a special device, way off the ingot mold according to the shape of the ingot: Some off the plunger pressed ingot ingot crane, lift the ingot mold with tongs; some with tongs pressed ingot mold, with the tweezers lift ingots.
4 charging crane:
Added to the open hearth in charge. Lord of the column with the bottom of the car to pick rod for stirring bins and place it into the furnace. The main column is rotatable about a vertical axis of rotation, pick rod can swing up and down and swing. Vice trolley for furnace repair and other auxiliary operations.
5 Forging crane: [1]
With forging hydraulic press used with large workpieces. Main car hanging on a hook turn special feeder to support and flip the workpiece; Vice trolley for lifting workpieces.
Lifting is a modern industrial production and transport of the production process of mechanization and automation of the important tools and equipment. So overhead crane and mining enterprises in the interior and exterior, steel chemical, railway transportation, port and logistics flow and other departments and sites are widely applied.