Electric pallet trucks transporting goods in time need to be careful
Electric pallet trucks transporting goods in time need to be careful. Allowed to operate loading, cargo piled unsafe or unstable to pay attention to security and stability, to prevent dumping and rollover accidents. If you load the front cover of sight, reverse driving. Not use defective or damaged pallets, so prone to accidents. Note To pallets on specialized areas, may not be placed at random. Driving forklifts need to slow down in the corner, warning whistle, to prevent collisions. Increased attention should pallet lift height, because it will also affect the stability of the truck. Also note that to avoid the heavy load operation of the forklift damage, work long hours in a continuous process, should pay attention to the mediation breaks; Should insufficient load capacity, be sure to switch to a larger truck, not overworked. When the pallet truck loaded onto a truck, the driver should pay attention to the total weight of the truck, and to ensure that the following matters: Ramps device on / under normal use trucks; truck tires were locked; there is enough space to accommodate the truck's door frame, if not accommodate, the door frame and the body needs to be loaded before the separation of transport. When loading cargo, cargo size should be connected to adjust the distance between the forks, the average weight of the goods should be shared equally by the two forks to avoid partial load or truck cargo run to the side of slippage. Fork into the stockpiles, fork side walls should be in contact with the goods, then pour the door frame, the fork is raised from the ground and then travel about 200 mm. Sharp high-speed driving is prohibited, in driving the process, lifting or lowering prohibited goods, etc., under the absolute prohibition of someone lifting frame. Across more than 7 lu slope carrying goods should be at the top of the slope of the goods. Carriage of goods may be made to the brakes and slow speed when driving to prevent cargo slide. When transporting bulky cargo, cargo block the line of sight, the truck should reverse at low speed. After non-stop to the engine idling and unattended, but not allowed to hang in the air cargo and the driver leaves the driving position. Battery pallet truck after stopping midway, when the engine is idling pour back door frame, when the engine stop the carriage should fall, and leaning forward to make the goods stand with. In the course of their work, that if a suspicious noise or unusual phenomenon, must immediately stop checks, take timely measures to exclude, in the absence of fault shall be excluded before continuing operation. After a day of work, the fuel tank filler respond, so not only can drive out the moisture inside the tank, but also can prevent moist gas at night cemented soluble oil in water droplets. In addition, without the consent of the company leadership, no person shall use forklifts. In order to improve the life of the truck and prevent accidents, in order to maintain the best running forklifts and various parts of the normal operation, in the course of the machine must be strictly carried out regular maintenance.
Chinese Dragon of increased truck scissor simple instructions
Chinese Dragon of increased truck scissor simple instructions: longlonglonglonglong Elevated scissor truck platform is a combination of truck and car at the same time to achieve the level of handling lifting platform provides the ability to apply mainly to the pipeline, conveyor belts and down goods, goods piled up, the position can be used as an adjustable workbench. Said by Category elevated scissor truck into manual, electric two, the user can choose the most suitable model according to the different conditions demand. Carrying capacity of 0.5 to 2.5 tons, lifting height of up to 800mm, 420mm when the forks raised the height of the front support legs and adjustable stabilizers will automatically extend snapping the ground to reach the braking effect become fixed platform, ensuring optimal stability and optimal braking performance.
the vertical mast . After the truck stop
Forklifts in use , the most important field finished goods fork to take - transit - goods unloaded into three basic steps destination. Here earthworm fork truck unloading goods technology, mainly divided into eight steps of action : longlonglonglong1 , approaching cargo pile . After starting the truck , according to the stacking position , driving the truck before driving to stacking, and then parked the truck . longlonglonglong2, the vertical mast . After the truck stop, the shift lever is placed in neutral position, push the joystick forward to tilt the mast to recover to a vertical position . longlonglonglong3 , adjust the fork height . Pull back the lift lever , the gap will increase to fork or pallet fork tines aligned holes under cargo . longlonglonglong4 , into the fork pickup. Gear shift lever forward , slow moving truck forward , so that the fork fork inserted into the hole . When wishbone quick hit of goods , parking. longlonglonglong5 , micro delivery fork. Pull back tilt lever , so that the fork truck can leave the run up to the height . longlonglonglong6 , after dumping the door frame . Tilting operation lever is pulled back , to the back of the door frame to the limit position . longlonglonglong7 exit of goods . The shift lever to reverse a file , so that the goods can fall back to the truck 's location. longlonglonglong8 , adjusting fork height . Forklift forward , heading Fanghuo locations.
creating a brand new "small crane"; three rolling machine with operators for protection
Small crane boom maintenance conditions, Jining Stone Construction Machinery Co., Ltd. specializes crane, small crane, mini crane, 10 t crane, 12 t crane, etc. complete. Requires that all parts intact and configuration can work, crane operation. To ensure that there is capacity in the case and no damage to the crane for lifting heavy objects are generally if it fails, there are many more accidents will occur, causing economic losses to the people. So check when a small jib crane carefully to ensure that it can make a good stretch rope, but also to ensure the boom conditions in their work better. Stone Construction Machinery Co., Ltd. Jining welcome customers to buy! " Small crane" attributed to special equipment, related to the safety of people's lives, more dangerous. Jining City, Shandong Province Bureau of Quality Supervision recently smitten on the area of ??some " small crane" making points gathered regulation to crack down on illegal production of " small crane." In view found that some illegal " small crane" making points as follows widespread doubt: First, the owners do not have the qualifications lifting machinery production, but no depict drawings and testing equipment, the mere own experiences, making lifting machinery; Second to save costs, the use of state banned the use of scrap automobile chassis production of " small crane" , through painting from scratch, creating a brand new " small crane" ; three rolling machine with operators for protection, not only out of production rolling machine, and secretly steal production of " small crane."
According to " Special Equipment Safety Supervision Act" rule, special equipment production units need special equipment supervision by the State Council administrative department promised, promised to obtain special equipment production qualification certificate, there is compatible with the production of technical personnel, skilled workers, production conditions and testing equipment, production process, it is necessary to have a sound management principles and responsibilities of criteria before they are allowed special equipment production activities. Such " small crane" rule fails to produce production point production, there is a big security risk, disrupted the market order, severe damage to the interests of consumers.